Glowshift Oil Pressure Gauge Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör fürs Wasser Glowshift Oil Pressure Gauge herunter. GlowShift Oil Pressure Gauge User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Tinted Series Oil Pressure Gauge
For Product Numbers: GS-T04
Wire Harness Color Code
Red:
12v Ignition Source (+) (switched)
Orange:
12v Switched Headlamp Source (+) (optional)
Black:
Vehicle Ground ( - )
Green:
Connect to the G Post on the Sensor
1. Disconnect the vehicle's negative battery cable.
Sensor Installation:
2. Install the oil pressure sensor. There are three common types of
oil pressure sensor installations:
Oil Gallery Test Port: Some engine oil galleries will have
a test port plug. Check your owner’s manual to verify the
location and thread size. Remove the port plug and install
the supplied pressure sensor. Additional adapters may be
required if the port is not threaded to 1/8
th
NPT.
Oil Filter Adapter Installation: You can purchase an Oil
Filter Sandwich Adapter from www.GlowShift.com. This
adapter installs between your oil filter and engine block,
providing you with 3 sensor ports in which you can install
the oil pressure sensor to.
T-Fitting Installation: Remove your stock oil pressure
sensor and fasten a T-fitting in its place. 1/8
th
NPT T-
Fittings are available for purchase at www.GlowShift.com.
Using a T-fitting allows you to “T” off of the port and
opens up 3 more, which then allows for the stock and
GlowShift sensors to be installed and operate
simultaneously.
Connecting the Power Wire Harness
3. Using automotive grade wiring (18 gauge); connect the green
wire to the “G” post of the pressure sending unit.
4. Connect a length of wire from the “WK” post of the pressure
sensor to any good (unpainted) ground connection.
Note: If this wire is not properly grounded the gauge
reading will be at full pressure.
5. To make the wiring of your gauges easier you can purchase an
expandable circuit. This component easily fits into your fuse
panel and provides an additional fused power wire for accessories
such as gauges. The expandable circuit is available for purchase at
www.GlowShift.com.
6. Using automotive grade wiring (18 gauge); connect the red
wire to a positive 12 volt ignition (switched) source. It may be
connected to the fuse panel, an accessory wire, or any positive 12
volt source that turns on and off with the ignition.
7. Using automotive grade wiring (18 gauge); connect the black
wire to any good (unpainted) ground connection. You may also
route a wire directly to the negative side of the vehicle’s battery.
8. The Night Time Dimming feature decreases the brightness of
the gauge face by 30%. Connect the orange wire to the 12 volt
positive headlamp source. This allows the mode to be activated
when the headlights come on. This step is optional and will not
affect operation of the gauge if it is omitted.
Note: Do not connect the orange wire to a dimmer
wheel. This will cause the gauge lighting to flicker.
9. Reconnect the vehicle's negative battery cable.
Power on the vehicle to ensure the gauge is functioning
properly.
Seitenansicht 0
1 2

Inhaltsverzeichnis

Seite 1 - For Product Numbers: GS-T04

Tinted Series Oil Pressure Gauge For Product Numbers: GS-T04 Wire Harness Color Code Red: 12v Ignition Source (+) (switched) Orange: 12v Switche

Seite 2

Additional Installation Information & Material Requirements  GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gauge

Kommentare zu diesen Handbüchern

Keine Kommentare