Glowshift Digital Series Tachometer Bedienungsanleitung PDF herunterladen

Digital Series Tachometer

For Product Numbers: GS-BD10 and GS-RD10

Wire Color Code

Red:

12v Ignition Source (+) (switched)

Orange:

12v Switched Headlamp Source (+) (optional)

Black:

Vehicle Ground ( - )

Green:

Connects to Vehicle’s Tachometer Source

1. Disconnect the negative battery cable.

Connecting the Power Wire Harness

2. Connect the green wire to the vehicle’s tachometer source wire or

negative side of the coil. You must consult your manual to ensure proper

location. If connecting to an aftermarket ignition system, be sure to

follow the manufacturer’s instructions for connecting a tachometer.

Please consult a service manual or mechanic before installing.

 Tachometer Test Wire: Some vehicles may have a tachometer

test wire to obtain a tachometer signal from. Consult your repair

manual or licensed mechanic to confirm the location of this

wire.

 Tachometer Adapter: It may be necessary to install a

Tachometer Adapter if you have a multiple coil system. You

can purchase a Tachometer Adapter from local auto parts store.

 Tachometer Filter: It may be necessary to use a Tachometer

Filter if you vehicle has either a points style or HEI ignition

system. You can purchase a Tachometer Filter from

www.GlowShift.com

 Note: Be sure to use a grommet when routing wires through

the firewall to protect them from stripping and damage.

3. Using automotive grade wiring (18 gauge); connect the red wire to a

positive 12 volt ignition (switched) source. It may be connected to the

fuse panel, an accessory wire, or any positive 12 volt source that turns on

and off with the ignition.

4. Using automotive grade wiring (18 gauge); connect the black wire to

any good (unpainted) ground connection. You may also route a wire

directly to the negative side of the vehicle’s battery.

5. The Night Time Dimming feature decreases the brightness of the gauge

face by 30%. Connect the orange wire to the 12 volt positive headlamp

source. This allows the mode to be activated when the headlights come on.

This step is optional and will not affect operation of the gauge if it is omitted.

 Note: Do not connect the orange wire to a dimmer wheel. This will

cause the gauge lighting to flicker.

6. Use the Cylinder Selection Switch on the back of the gauge to set the

number of engine cylinders on the tachometer to match that of your vehicle.

Do this before applying power to the gauge.

 If you need to change the cylinder selection, you must remove power

from the gauge, make your selection, and then reapply power to the

gauge for proper calibration.

Switch #

Cylinders

7. Reconnect the negative battery cable.

1 2 3

Digital Series Tachometer 1

Inhaltsverzeichnis

Seite 1 - Digital Series Tachometer

Digital Series Tachometer For Product Numbers: GS-BD10 and GS-RD10 Wire Color Code Red: 12v Ignition Source (+) (switched) Orange: 12v Switched Hea

Seite 2

Additional Installation Information & Material Requirements  GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gaug

Seite 3

2. EXCLUSIVE REMEDY; ACCEPTANCE: Purchaser's exclusive remedy and GlowShift's sole obligation is to supply (or pay for) all labor necess

Verwandte Modelle: Tachometer Gauge

Kommentare zu diesen Handbüchern

Keine Kommentare

Glowshift Digital Series Tachometer Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Glowshift Digital Series Tachometer herunter. GlowShift Digital Series Tachometer User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: Tachometer Gauge

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Glowshift Digital Series Tachometer